AUDIOQUEST IRISH RED
Scrivi la tua recensione
AUDIOQUEST IRISH RED
ART091780
Pagamento sicuro con Bonifico Bancario, Paypal e carte di credito o Rate Banca Sella
Richiedi la disponibilità del prodotto prima dell'acquisto
Consegna veloce in 24/48 ore, in base alle tempistiche di disponibilità del prodotto
Reso garantito entro 14 giorni per problematiche dell'articolo
SOLID 0.5% SILVER CONDUCTORS
Solid .5% Silver-Plated Copper Conductors: A superbly cost-effective way to turn up the “sharpness” for a subwoofer, enhancing articulation and intelligibility.
Metal-Layer Noise-Dissipation
It's easy to accomplish 100% shield coverage. Preventing captured radio-frequency interference (RFI) from modulating the equipment's ground reference requires AQ's Noise-Dissipation. Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical "reference" ground plane, which in turn causes a distortion of the signal. Noise-Dissipation "shields the shield," absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground.
Foamed-Polyethylene Insulation
Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. Because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile, Foamed-PE, with its high air content, causes much less of the out-of-focus effect common to other materials.
Symmetrical Coax Geometry
Identical positive (+) and negative (-) conductors prevent the shield from being used as an inferior audio conductor.
Cold-Welded, Gold-Plated Terminations
This plug design allows for a connection devoid of solder, which is a common source of distortion. Instead of solder, the process employs a high-pressure technique. Because the ground shells are stamped instead of machined, the metal used can be chosen for low distortion instead of machinability.
SPECIFICS
Metal
Solid 0.5% Silver
Noise Dissipation
Metal-Layer
Geometry
Symmetrical Coax
Terminations
Cold-Welded, Gold-Plated
Signal Type
Analog
Cable Length
2 m = 6 ft 6 in
Jacket
Red on Black Braid
Sold As
Single Cable
Weight
0.4 lb
(Part Number: )
Solid .5% Silver-Plated Copper Conductors: A superbly cost-effective way to turn up the “sharpness” for a subwoofer, enhancing articulation and intelligibility.
Metal-Layer Noise-Dissipation
It's easy to accomplish 100% shield coverage. Preventing captured radio-frequency interference (RFI) from modulating the equipment's ground reference requires AQ's Noise-Dissipation. Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical "reference" ground plane, which in turn causes a distortion of the signal. Noise-Dissipation "shields the shield," absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground.
Foamed-Polyethylene Insulation
Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. Because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile, Foamed-PE, with its high air content, causes much less of the out-of-focus effect common to other materials.
Symmetrical Coax Geometry
Identical positive (+) and negative (-) conductors prevent the shield from being used as an inferior audio conductor.
Cold-Welded, Gold-Plated Terminations
This plug design allows for a connection devoid of solder, which is a common source of distortion. Instead of solder, the process employs a high-pressure technique. Because the ground shells are stamped instead of machined, the metal used can be chosen for low distortion instead of machinability.
SPECIFICS
Metal
Solid 0.5% Silver
Noise Dissipation
Metal-Layer
Geometry
Symmetrical Coax
Terminations
Cold-Welded, Gold-Plated
Signal Type
Analog
Cable Length
2 m = 6 ft 6 in
Jacket
Red on Black Braid
Sold As
Single Cable
Weight
0.4 lb
(Part Number: )