Scrivi la tua recensione
ANTHEM M1
ART074436
Pagamento sicuro con Bonifico Bancario, Paypal e carte di credito o Rate Banca Sella
Richiedi la disponibilità del prodotto prima dell'acquisto
Consegna veloce in 24/48 ore, in base alle tempistiche di disponibilità del prodotto
Reso garantito entro 14 giorni per problematiche dell'articolo
Finale di potenza monofonico a tecnologia digitale. Potenza 1000W su 8ohm, 2000W su 4ohm e 2400W 3 ohm. Funzionamento in classe D. Ingressi RCA e XLR. Trigger 12V. Costruzione dello chassis Slim Line per facilitare il montaggio a rack.
Power Output continuous, 20 Hz to 20 kHz, <0.1% THD + N
8 O 1000 W
4 O 2000 W
3 O 2400 W
2 O> 2000 W depending on line voltage regulation
With 120V AC supply the amplifier's maximum output into impedances 4 O and lower, as well as its maximum duration.
Frequency Response 20 Hz to 20 kHz
Open circuit +/- 0.1 dB
8 O +/- 0.1 dB
4 O +/- 0.1 dB
2 O +/- 0.2 dB
Power Bandwidth 1000 W at 8 O 5 Hz to 45 kHz
THD + N at 1 kHz, 8 O
1 W 0.01%
10 W 0.01%
100 W <0.03%
1000 W <0.06%
IMD 19 kHz + 20 kHz, CCIF 0.003%
S / N Ratio ref. 1000 W, IEC-A 113 dB
Voltage Gain 29 dB
Input Sensitivity 100 mV for 1 W output, 3.2 V for 1000 W output (8 O)
Input Impedance 10 kO (RCA), 20 kO (XLR)
Damping Factor 800 to 1400 depending on frequency
XLR Configuration Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
POWER REQUIREMENTS
Consumption in a typical music / theater installation
standby mode, 120V mains <1W
standby mode, 240V mains <2W
operate mode, idle 33 W
typical operation 300 W
Where mains voltage is 120V, one dedicated 15A circuit for amplifier is recommended dependent on speaker. A 20A circuit is adequate for two amplifiers playing music where speaker impedance is 8 O. This product operates from single phase AC power source that supplies between 108V and 264V at a frequency of 50 or 60Hz.
DIMENSIONS
Height with feet 2 1/4 inches (5.7 cm)
Height without feet 1 rack unit
Width standard handles 19 1/4 inches (49 cm)
Width rackmount handles 19 inches (48.3 cm)
Depth 18 3/4 inches (47.6 cm)
Weight (unpacked) 20 lb (9 kg)
(Part Number: ART074436)
Power Output continuous, 20 Hz to 20 kHz, <0.1% THD + N
8 O 1000 W
4 O 2000 W
3 O 2400 W
2 O> 2000 W depending on line voltage regulation
With 120V AC supply the amplifier's maximum output into impedances 4 O and lower, as well as its maximum duration.
Frequency Response 20 Hz to 20 kHz
Open circuit +/- 0.1 dB
8 O +/- 0.1 dB
4 O +/- 0.1 dB
2 O +/- 0.2 dB
Power Bandwidth 1000 W at 8 O 5 Hz to 45 kHz
THD + N at 1 kHz, 8 O
1 W 0.01%
10 W 0.01%
100 W <0.03%
1000 W <0.06%
IMD 19 kHz + 20 kHz, CCIF 0.003%
S / N Ratio ref. 1000 W, IEC-A 113 dB
Voltage Gain 29 dB
Input Sensitivity 100 mV for 1 W output, 3.2 V for 1000 W output (8 O)
Input Impedance 10 kO (RCA), 20 kO (XLR)
Damping Factor 800 to 1400 depending on frequency
XLR Configuration Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
POWER REQUIREMENTS
Consumption in a typical music / theater installation
standby mode, 120V mains <1W
standby mode, 240V mains <2W
operate mode, idle 33 W
typical operation 300 W
Where mains voltage is 120V, one dedicated 15A circuit for amplifier is recommended dependent on speaker. A 20A circuit is adequate for two amplifiers playing music where speaker impedance is 8 O. This product operates from single phase AC power source that supplies between 108V and 264V at a frequency of 50 or 60Hz.
DIMENSIONS
Height with feet 2 1/4 inches (5.7 cm)
Height without feet 1 rack unit
Width standard handles 19 1/4 inches (49 cm)
Width rackmount handles 19 inches (48.3 cm)
Depth 18 3/4 inches (47.6 cm)
Weight (unpacked) 20 lb (9 kg)
(Part Number: ART074436)
ART074436
